Packaging GuidesNovember 22, 20263 min read

How to Pack Flat-Pack Furniture for Shipping

Flat-pack furniture components packaged for courier shipping and safe transport

Flat-pack furniture components — boards, shelves, frames, glass panels, and hardware bags — are awkward to ship because they're long, often heavy, and their surfaces scratch easily. The main risks are surface damage, bending under their own weight, and hardware bags puncturing or falling out of packaging.

This guide covers how to prepare each type of flat-pack component for safe courier delivery.

Before You Pack: Check Size Limits

Long flat-pack components frequently exceed standard parcel size limits. Standard courier limits for the longest side are typically 120–150 cm, with total girth (length + 2× height + 2× width) limited to 300 cm. A bookcase board can easily be 180–200 cm. If any single piece exceeds the courier's limits, it must be shipped as oversized freight or via a pallet booking.

Packing Wooden and MDF Boards

  1. Protect edges and corners with cardboard edge protectors or foam strips. Edges are the most vulnerable part — they chip, scratch other surfaces, and puncture packaging.
  2. Wrap finished surfaces (lacquered, foil-wrapped, or veneered boards) in bubble wrap or foam sheeting — not directly in tape, which can mark or lift the surface.
  3. Bundle multiple boards of similar size together and wrap as a unit. Interleave foam or cardboard between boards to prevent scratching.
  4. Place boards in a cardboard box that fits closely. Loose boards can rock and cause internal damage. If the box is wider than the boards, fill the gap with cardboard padding.

Packing Glass Shelves and Panels

Glass shelves from flat-pack furniture are thin and can shatter from point pressure. Apply tape in a cross pattern across the glass surface. Fit foam corner guards. Wrap in two full layers of bubble wrap. Pack separately from wooden boards — never place glass in direct contact with other hard surfaces.

Packing Hardware and Small Parts

Screws, bolts, dowels, hinges, and cam locks must be contained securely. Loose hardware can puncture packaging from the inside or be lost if a bag tears. Seal original hardware bags with tape. Place all hardware in a zip-lock bag or sealed envelope. Tape this firmly inside the main box, not loose at the bottom where it can be missed when unpacking.

Assembly Instructions

If sending the original assembly instructions booklet, slip it into the hardware bag or place it flat against the side of the box (not at the bottom where it can be bent). Consider photocopying or scanning instructions and including a printed copy inside, keeping the original.

Common Questions

Can I reuse the original flat-pack furniture box?

If the original box is undamaged, it's ideal. The original box is sized specifically for the components and usually has internal dividers that keep parts separated. Check the base carefully — original flat-pack boxes are sometimes made from lighter cardboard that can fail under repeated handling. Reinforce base seams with heavy packing tape.

Should I ship a whole flat-pack set together or in multiple boxes?

Shipping all components together is preferable — it simplifies delivery and reduces the chance of a partial delivery. If the total weight or size exceeds parcel limits, split sensibly: boards in one box and hardware/glass in a separate smaller box, labelling both boxes clearly as part of a set.

Get an Instant Shipping Quote

Compare carrier rates in seconds. Door-to-door delivery worldwide.

Compare Rates Now →

Related Articles

Person inspecting a used cardboard box for reuse in shipping — checking structural integrity
Packaging Guides

How to Safely Reuse Boxes for Shipping

Reusing cardboard boxes for shipping is both economical and environmentally sensible. Most corrugated cardboard boxes retain good structural strength after a first use, as long as they haven't been wet, crushed, or heavily creased.

November 22, 2026
Automotive parts packaged for courier shipping in a logistics warehouse
Packaging Guides

How to Pack Automotive Parts for Shipping

Automotive parts present a wide range of packaging challenges. A gear knob and a front bumper require completely different approaches. Getting the packaging right matters both for the part itself and for other parcels in the same delivery vehicle — heavy metal parts that break free from poor packaging can damage everything around them.

November 22, 2026
Large packaged electronics shipment prepared for courier collection and safe transit
Packaging Guides

How to Pack a TV for Shipping: What to Do When You Don't Have the Original Box

Modern flat-screen televisions are fragile in ways that aren't obvious from handling them. The screen panel can be cracked by pressure on the back of the unit, vibration can damage internal components, and the edges and corners are susceptible to impact damage. Without correct packaging, a TV that survived years on a wall can arrive at its destination with a shattered screen.

November 22, 2026
Double-boxed fragile shipment being prepared by warehouse staff for courier collection
Packaging Guides

How to Double-Box Fragile Items for Maximum Protection

Double boxing is one of the most effective packaging techniques for fragile, high-value, or shock-sensitive items. The principle is simple: an inner box protects the item, and an outer box absorbs and distributes impact before it reaches the inner box. The cushioning layer between them is what makes the system work.

November 22, 2026

Powered By

powered-by-0powered-by-1powered-by-2powered-by-3

Supported Payments

supported-payment-0supported-payment-1supported-payment-2supported-payment-3supported-payment-4