The right packaging material depends on what you are shipping, how far it is going, and how the carrier will handle it. Using the wrong material is one of the most common reasons claims for damage are rejected — carriers have specific packaging requirements, and ‘insufficient packaging’ is the most frequent grounds for refusing a claim.
Cardboard Boxes
Cardboard is the standard outer packaging for most shipments. The thickness is measured by wall count:
- Single wall (3-ply): suitable for light items up to around 10 kg on short or intra-EU routes.
- Double wall (5-ply): recommended for items between 10 and 30 kg, fragile goods, or any shipment travelling a long distance or passing through multiple hubs.
- Triple wall (7-ply): heavy or industrial goods, or when the box itself provides the primary structural support for the contents.
Choose a box that fits the item with enough room for cushioning material on all sides, but not so large that the item shifts. A box where the item moves when shaken will not pass a carrier’s inspection if a claim is made.
Bubble Wrap
Bubble wrap provides cushioning against impact. The bubble size matters:
- Small bubbles (10 mm): general purpose, good for lightweight fragile items such as glassware, ceramics, and small electronics.
- Large bubbles (20–30 mm): heavier or larger items where greater impact absorption is needed.
- Anti-static bubble wrap (black or pink): essential for circuit boards, computer components, and electronics that are sensitive to static discharge.
Wrap bubble wrap with the bubbles facing the item, not outward. This maximises cushioning where it matters.
Kraft Paper and Packing Paper
Crumpled kraft paper is an effective void filler and a sustainable alternative to plastic packing peanuts. It works well for filling gaps around non-fragile items and protecting surfaces from scratching. Heavier gauge paper (90–120 gsm) is suitable for wrapping items; standard tissue paper is not adequate for shipping.
Packing Peanuts and Loose Fill
Loose fill is good for filling large volumes of void space around multiple smaller items. Modern biodegradable peanuts (made from starch) dissolve in water and have largely replaced polystyrene for most purposes. The limitation of loose fill is that it compresses under sustained weight, so it is less suitable as the primary cushioning for heavy items.
Foam
Foam provides firm, consistent cushioning that does not compress over time the way loose fill does:
- Closed-cell polyethylene foam: firm, water-resistant, used as sheets or blocks for cushioning heavier items. Available in rolls for cutting to size.
- Open-cell foam: softer, used for delicate surfaces (wrapping electronics, instruments, optical equipment).
- Custom-cut foam inserts: used for high-value items (cameras, instruments, medical devices) where a precise fit eliminates movement entirely.
Foam Boards and Rigid Mailers
Flat items that must not bend — artwork, photographs, documents, printed circuit boards — should be sandwiched between two rigid sheets of foam board (sometimes called Foamex or Foamcore) before boxing. Rigid cardboard mailers (marked ‘Do Not Bend’) are suitable for lighter flat items on shorter routes.
Packing Tape
The tape used to seal a box is load-bearing: a poorly taped box can burst open in transit. Use at minimum 48 mm wide packing tape applied in an H-pattern — along the centre seam and across each short edge. For heavy boxes, reinforced or filament tape adds tensile strength. Water-activated gummed tape (brown kraft tape) provides the strongest bond of all, penetrates the cardboard fibres, and is tamper-evident.
Desiccants and Silica Gel
For moisture-sensitive shipments — electronics, leather goods, certain pharmaceutical products, some food items — include one or more silica gel sachets inside the packaging. This is particularly important for sea freight (high humidity in containers), shipments to humid climates, or any item in transit for more than a week. The sachet absorbs ambient moisture and prevents condensation forming inside the package.
The Shake Test
Before sealing any parcel, shake the box gently. If you can hear or feel the contents moving, add more cushioning material until there is no movement. This is the standard that carriers and loss-adjusters apply when assessing whether damage resulted from insufficient packaging. A parcel that passes the shake test has met the basic packaging requirement for most shipments.




